Low additional load
- individual skier/snowboarder, riding softly, not falling
- group with good spacing (minimum 10 m) keeping distances
High additional load
- two or more skiers/snowboarders etc. without good spacing (or without intervals)
- snow machine
- single hiker/climber
Mountain terrain unconnected to a ridgeline.
Often refers to transitions from extremely steep to less steep terrain. Steep terrain and stone steps not connected to the main ridge belong in this category. There is no clear boundary line between areas adjacent to or distant from a ridge, it is a transitional zone.
Size 2: medium avalanche
- could bury, injure or kill a person
- snow avalanche stops typically at the end of a slope
Size 3: large avalanche
- could bury and destroy a car, damage a truck; destroy a small building or break a few trees
- snow avalanche could traverse flat terrain (considerably below 30°) over distances of less than 50 m
Size 4: very large avalanche
- could bury and destroy a railway car, large truck, several buildings or a piece of forest
- snow avalanche traverses flat terrain (considerably below 30°) over distances more than 50 m and can reach valley ground
Size 5: extremely large avalanche
- could gouge the landscape; disastrous damage potential
- snow avalanche reaches valley ground; largest runout distance known
Snow is “bonded” if the particles are interlinked (sintered) to such a degree that a carefully isolated block does not collapse upon itself. Bonded snow can be soft or hard.
New fallen snow is a burden on the existing snow cover, can thus increase avalanche danger.
In unfavourable conditions, e.g. poor layering, low temperatures, strong winds, even a few cm can be critical. In favourable conditions, e.g. stable old snowpack, light winds, even 50 cm of snow presents no problem.
Evolving avalanche danger over the course of a day. Avalanche danger can vary greatly during the day. Springtime situations are typical: after a clear night, avalanche danger is low early in the morning, then increases over the course of the day due to daytime warming and solar radiation. Also common while heavy snowfall, prolonged wind activity and rain.
Large, hollow crystals with edges, rims and facets on the surface, the result of faceting amidst high internal temperature disparities.
Characteristic grain size: 2 to 5 mm or larger
Depth hoar is an accumulation of cup-shaped crystals. Weak layers are rather often made of depth hoar.
See also: www.snowcrystals.it
Glacier ice which breaks and plunges over a steep step, sometimes sweeping snow in the avalanche track with it. Often responsible for large-scale disasters.
|1895||Altels (Switzerland)||6 fatalities, 158 cattle killed|
|1965||Mattmark (Switzerland)||88 fatalities|
|1970||Huascaran (Peru)||with subsequent debris flow: 18‘000 fatalities|
External radiation which strikes the snowpack.
Shortwave radiation is largely (up to 90 %) reflected from the snow surface, depending on type of snow. The remainder warms the uppermost layers of the snowpack and possibly moistens them.
Long-wave (infrared radiation) radiation is almost completely absorbed by the snow surface.
Areas enclosed by high alpine ridges, subject to intensified precipitation.
Typical inneralpine regions are central Valais, Engadine and central Grisons (CH), located between Northern Alpine Ridge and Main Alpine Ridge; Ortler-Vinschgau region (I), Oetz Valley (A).
In France, the following are considered inneralpine regions: Vanoise, Maurienne, Grandes-Rousses and Oisans-Pelvoux, as well as the mountain region near the French-Italian border.
In Spain, the area of Cerdanya (Perafita-Pulgpedrés) in the Catalonian Pyrenees is included.
Transformation process of dry snow with great temperature disparity inside the snowpack: the crystals decompose into faceted, hollowed grains; the crystals grow in size, the hollows recede, the bonding decreases, lowering the firmness of the transformed layers. The greater the temperature disparity, the more intense is the transformation.
The process is accelerated in shady terrain with shallow snow cover. This process can affect the whole snowpack or only some parts of the snowpack. Layers of faceted crystals are often found near to crusts. On the snow cover surface it preferably develops during clear sky nights.
Slopes in shadow, untouched or little struck by sunlight, typically north-facing.
More prevalent in December and January, due to lower solar angles, than in spring. Mountains can cast shadows on surrounding slopes in any aspect; thus, not only north-facing slopes are shady.
The abrupt release of a snow board (slab) on a mountain slope.
After crack initiation and crack propagation in a weak layer the snowcover is divided in three parts: The weak layer, the gliding horizon and the slab. If slope angle is steep enough, the slab will glide down. If the slope is not steep enough, the slab will settle down on the broken weak layer. Possibly a whumpf will follow due to air pressed out of the weak layer.
The fracture is sharply edged.
A mudflow-like avalanche composed of slush—very saturated snow. Commonly occurring after rainfall and/or intense thawing have produced more water than can drain through the snow. Slush avalanches can occur on very gentle slope angles. They usually occur in Arctic climates on permafrost soil when dry depth hoar becomes rapidly saturated with water in spring.
The mass per unit volume of a given quantity of snow. Snow can have highly varied densities:
|Snow type||Density [kg/m³]|
|very light new snow||approx. 30|
|new snow||approx. 100|
|decomposing and fragmented precipitation particles||150 – 300|
|rounded snow||250 – 450|
|faceted snow||250 – 400|
|depth hoar||150 – 350|
|wet snow||300 – 600|
|firn||600 – 830|
|glacial ice||approx. 900|
The result of snow transport. Drifting and blowing snow usually forms a dense layer deposited on lee slopes, often with brittle, fragile bonding. Areas prone to drifting are gullies, bowls, slope discontinuities and areas adjacent to ridgelines.
Snow masses transported by wind. Three main processes take place: rolling, saltation and suspension. During transport, snow crystal size decreases considerably, depending of wind speed and duration, up to 10 to 20 % of its original size. The small fractured particles are closely packed by wind, bringing about a cohesive snow layer (a dense-cohesive slab or a soft-cohesive slab) on the lee slope. The colder snow is while forming a deposit, the more brittle the deposit is.
Size of snow drift accumulations (thickness)
- small snow drift accumulations: 5- 20 cm thick
- medium snow drift accumulations: 20 – 50 cm thick
- large snow drift accumulations: thicker than 50 cm
Extent of snow drift accumulations (spatial)
- some snow drift accumulations:
very little snow drift accumulation with small spatial extent
- extensive snow drift accumulations:
major snow drift accumulations mostly with large spatial extent on slopes of all aspects
The height of the water column if a snow sample is melted (measured in millimeters), with reference to the same area. The water equivalent of a 20 cm snow sample with a mean snow density of 100 kg/m³ is 20 mm. With a density of 500 kg/m³ the equivalent of a 20 cm snow sample is 100 mm of water.
Change in temperature per unit distance of depth, expressed in °C/m or °C/cm.
The temperature gradient is recorded in the snowpack vertically from the ground to the surface. It is determined as the difference between adjacent measurements. For example a “small” temperature gradient is 1 °C per meter, a “large” temperature gradient is 25 °C per meter.